How To Set Up Travel Trailer Hitch

Weight Distribution Hitch Setup

How to Set Up a Weight Distribution Hitch - CURT

Weight Distribution Hitch Setup

8 Like shooting fish in a barrel-to-Follow Steps!

Weight distribution hitch installation involves leveling the trailer, measuring vehicle and trailer superlative, mounting the hitch head, shank, spring bars and hookup brackets, and adjusting the weight distribution hitch every bit needed.

In this guide, we will cover step by step how to set up a weight distribution hitch. Each hitch is unique, so make certain you follow the instructions included with your detail model.

Weight Distribution Hitch Installation Video

How to Install and Adjust Your Weight Distribution Hitch

Pace 1: Measure vehicle and trailer top

Park your vehicle and trailer on a level surface and employ the trailer tongue jack and a level to brand sure your trailer is parallel with the ground.

Measure and tape the height of your vehicle and trailer. You will need to know the distance from the ground to the top of the trailer coupler and the distances from the footing to the bottom of the rear bumper and front bumper on your tow vehicle. You can as well employ the distance from the footing to wheel well if you prefer.

Step ii: Attach the WD shank and hitch caput

Insert the weight distribution shank into the receiver tube. Exist sure that the shank is fully inserted in the receiver tube of your trailer hitch and secure information technology using a hitch pivot & clip.

Position the caput assembly on the adjustable shank. The caput should be raised into position so that the top of the trailer brawl is one to three inches above the coupler height. Use one mounting bolt at the bottom of the assembly to hold it in place, but do non tighten with a nut.

Need more drib or ascent? Shop replacement shanks

Stride three: Prepare weight distribution hitch caput bending

Pivoting the caput downward, place two washers on the adjustment rod and insert the rod into the lower hole on the head. Some weight distribution hitches may non crave this step, having a different adjustment mechanism. Remember to consult the instructions specific to your weight distribution hitch.

Rotate the head up into the mounting position on the shank. Information technology should be vertical or tilted slightly back. You may need to add or remove washers to achieve the proper angle.

Finally, insert the second bolt into the top pigsty in the hitch head and fasten both bolts with the provided nuts and washers. Tighten the bolts but only enough to concord the head in identify.

Step iv: Install spring bars and couple the trailer

Mountain the jump bars on the hitch head. If the leap bar chains have not yet been attached, attach them to the bound bars before mounting the confined to the head.

Enhance the trailer coupler, and back the tow vehicle up to couple the trailer to the trailer ball.

Stride 5: Raise the trailer jack

With the coupler latched onto the trailer brawl, lift up the coupling point using the trailer jack. The coupler should be raised well-nigh 3 inches to a higher place the level position.

Stride 6: Engage the hookup brackets

Position the spring bar hookup brackets on the trailer frame using the spring bar chains equally a guide. Mount the brackets onto the trailer frame using the provided bolts.

Then, attach the bound bar chains to the brackets. Make sure both sides are spaced the aforementioned vertically, with number of concatenation links between the spring confined and the hookup brackets. So pry the brackets into the locked position using the provided lift handle.

Note: There must exist a minimum of five concatenation links between the bracket and the spring bar.

Step 7: How to arrange weight distribution hitch

Retract the trailer jack and so that the full weight of the trailer is resting on the hitch. So, re-measure the distances between the ground and the front and rear bumpers. Each distance should exist within 1/2" of the original measurement. If the distances have inverse too drastically, you lot tin adjust the number of links on the bound bar chains to increment or subtract tension. You lot can also adapt the tilt of the head unit.

Step viii: Fully tighten the bolts

Uncouple the trailer and torque all hardware to the values specified in the instructions.

Weight distribution setup differs across various models. With your weight distribution hitch, always follow the instructions provided by the manufacturer, and call up to take your time.

Weight distribution and sway control in one product!

The TruTrack™ weight distribution hitch features an innovative design that levels the vehicle-trailer combination, while actively keeping the trailer from swaying.

No need for a separate sway control unit!

Back to Weight Distribution Hitches