How To Set Up Shisha

How to Setup a Shisha Piping

one. Preparing your piping

Make sure your pipe is clean and dry earlier using it. Start off by filling the glass base with h2o and then that approximately 1 inch of the metallic tube is submerged below the water line. The area left above this is where the smoke volition mix with air and cool farther. Too much water makes information technology hard to suck the fume through and leaves little space left for the smoke to mix with air resulting in much stronger smoke.

Adhere the Pipe (Stem) onto the glass water bottle base, place the rubber hose grommet in the hole then adhere the hose to the piping every bit shown in the image below:

2. Preparing the molasses

If y'all're new to using a Shisha pipage, offset off by trying a small corporeality of Molasses beginning to practise getting it right. Place the Molasses into the clay basin.  We recommend almost 8g of Molasses per smoke. Break upward the Molasses rather than putting information technology in to ensure the molasses are non compacted otherwise the air volition not pass through and will brand the smoke potent and give a burnt season (see image below).

TIP: Using a cocktail stick, endeavor to make a hole the size of a pencil in the middle so that you can meet the central hole in the base. THis will permit for ameliorate airflow and improve smoking feel.

Identify the metal charcoal tray on the pipe, the rubber grommet in clay bowl then finally the clay bowl onto the pipage to ensure an air tight seal (see diagram below).

Take a small piece of aluminium foil, big enough to embrace the opening of the bowl.  Wrap the foil over the top so that the surface is tight.  Use a toothpick to punch v-six holes in the foil. Yous may want to suck on the mouth piece to run into if enough air flows through the pipage. If its an endeavor to draw air you may want to brand some more pigsty or ensure the tobacco is not too tightly packed. Try to brand one of the holes get correct through into one of the the holes in the bowl.

TIP: Accident into the oral cavity slice to clear any molasses that may cover the central hole(s).

3. Lighting the charcoal

If you lot are using Self Igniting coal (due east.grand. Swift Lights) then calorie-free the charcoal and wait about 1 minute subsequently it has stopped sparkling before placing it on the foil using the tongs provided. If yous are using Natural Charcoal, light information technology somewhere condom (like your cooker) and wait until it is glowing before placing information technology on the foil. PLEASE Note: If you lot place the charcoal on the foil too early you'll be smoking the charcoal fumes before yous go any flavour.

TIP: Try placing the charcoal on the outside of the bowl and working information technology around the edges of the basin.  The centre of the bowl should be the final place your charcoal is placed.

If you accept a Windcover, apply it to prevent the charcoal falling off in case someone knocks your piping. A wind cover also preserves charcoal by keeping the heat from escaping. (See paradigm beneath).

Congratulations, your Shisha pipe is at present ready to smoke! Suck on the hose (with a mouth tip on the end of the hose if necessary) to describe fume. we advise sucking gently to start with and so the molasses heats gently, sucking too hard volition result in the height molasses burning which will taint the remainder of if with a charred taste. Long gentle draws will help the heat pass through the tobacco.

Finally, add some friends and bask!

Safety Tips

• Always apply tongs or another appropriate utensil when handling hot charcoal
• Brand sure the charcoal that you are using is non crumbly before lighting it or you'll accept problem transferring information technology from the charcoal pan to the pipe.
• Low-cal the charcoal outside or in the kitchen. If smoking indoors, this volition forestall your 'smoking' room from filling upwardly with unwanted charcoal smoke. This will also protect your carpeting in the unlikely event some sparks fall onto the rug.
• Ensure the hookah pipe is stable before placing the charcoal. It's a adept thought to place the pipe on a difficult flat surface such as a large tile bachelor from whatever DIY store. If yous have expensive carpets you may desire to identify a thick cotton wool sheet effectually the smoking area in case you lot knock the pipe over.
• Use a large wind cover to prevent the charcoal falling off if you're used to using a big quantity of tobacco or round natural charcoal.

Source: https://www.theshishashop.com/pages/how-to-setup-a-shisha-pipe

Share this post